Light Distance Exposure Calculator (Inverse Square)
Author: Fiat Lux Guides Editorial Team Reviewer: Fiat Lux Guides Editorial Team Most recently reviewed First published Filed under Tools
Moving a small light source to a new distance changes subject illuminance by the square of the distance ratio, so doubling the distance cuts the light to one-fourth (two stops darker). Enter your starting and new distances below to calculate the exact stop change, compensating aperture, manual flash power step, or guide-number f-stop.
Light distance calculator
Point-source caveat: the inverse-square law holds for a small source. A large softbox or window close to the subject falls off more slowly than this calculator predicts. (HyperPhysics, accessed 2026-11-14) Unconfirmed: check the manufacturer's spec
Nothing you type leaves this page or is stored.
Choose Calculate to see the result.
Formulas and sources
- Illuminance from a small source falls in proportion to 1/d^2: E2/E1 = (d1/d2)^2 (HyperPhysics, accessed 2026-11-14)
- One stop (1 EV) is a factor of 2 in light; dEV = log2(E2/E1) = 2*log2(d1/d2); one stop of distance is a factor of sqrt(2) (Wikipedia, accessed 2026-11-14) Unconfirmed: check the manufacturer's spec
- f-number N is proportional to 1/sqrt(light): N2 = N1 * (d1/d2) keeps exposure constant (Wikipedia, accessed 2026-11-14) Unconfirmed: check the manufacturer's spec
- Guide number GN: aperture N = GN / distance, GN quoted at ISO 100 in the unit the manual states (metres or feet); scales with sqrt(ISO/100) (Sony help guide, accessed 2026-11-14) Unconfirmed: check the manufacturer's spec
- Manual flash power is set in steps from 1/1 to 1/128; each halving is one stop (Canon manual, accessed 2026-11-14)
Belongs to the guide: Free Photo and Video Lighting Tools
Checked by Fiat Lux Guides’ editorial desk against the cited sources.
Use this calculator from the Fiat Lux Guides lighting tools hub to find how moving a continuous light or flash changes exposure, or to convert a flash guide number into a working f-stop.
How the Inverse Square Calculation Works
The inverse square law states that light from a point source spreads over the surface of a sphere whose area grows with the square of the distance. As HyperPhysics explains, illuminance ($E$) falls in proportion to $1 / d^2$, so comparing two distances $d_1$ and $d_2$ gives the illuminance ratio:
$$E_2 / E_1 = (d_1 / d_2)^2$$
Because camera exposure is measured in stops (EV), where each 1-stop change doubles or halves the light reaching the sensor, the change in stops ($\Delta\text{EV}$) is the base-2 logarithm of that ratio:
$$\Delta\text{EV} = \log_2\bigl((d_1 / d_2)^2\bigr) = 2 \cdot \log_2(d_1 / d_2)$$
A positive $\Delta\text{EV}$ means the light moved closer and the subject receives more light; a negative $\Delta\text{EV}$ means the light moved farther away and the subject receives less light. To compensate with aperture alone from a starting f-number $N_1$, multiply by the square root of the light ratio:
$$N_2 = N_1 \cdot (d_1 / d_2)$$
In guide-number mode, the required f-number equals the guide number ($\text{GN}_{100}$) divided by the flash-to-subject distance $d$ (using the same unit—meters or feet—listed in the flash manual), scaled for ISO:
$$N = \frac{\text{GN}_{100} \cdot \sqrt{\text{ISO} / 100}}{d}$$
For manual flash power, halving the power setting (such as moving from 1/1 to 1/2, or 1/2 to 1/4) reduces output by 1 stop. For more on how continuous lights and flashes differ in output control, see continuous LED lights for beginners and speedlights compared with studio strobes.
Worked Example
Suppose you meter a small flash at $d_1 = 2.0\text{ m}$ and get a correct exposure at $f/5.6$. You then move the flash back to $d_2 = 2.83\text{ m}$ (about $2 \times \sqrt{2}$).
- Illuminance ratio: $(2.0 / 2.83)^2 \approx 0.50$ (half as much light).
- Stop change: $2 \cdot \log_2(2.0 / 2.83) \approx -1.00\text{ EV}$ (1 stop darker).
- Aperture compensation: $N_2 = 5.6 \cdot (2.0 / 2.83) \approx 3.96$, which rounds to $f/4$ (1 stop wider). Alternatively, you could double the flash power (e.g., from 1/4 to 1/2) or double the ISO (e.g., from ISO 100 to ISO 200).
For a guide-number example, take a speedlight rated at $\text{GN} = 30\text{ m}$ at ISO 100 (the Sony HVL-F46RM lists GN 30 at its 50 mm zoom setting, 35 mm format, full power, ISO 100). At $d = 3.0\text{ m}$ and ISO 100, the starting aperture is $30 / 3.0 = f/10$. At ISO 400, $\sqrt{400 / 100} = 2$, so the effective guide number doubles to $60\text{ m}$ and the aperture becomes $f/20$.
Assumptions and Limits
- Small-source assumption: The formula assumes a point source radiating freely. Large softboxes or window light portrait setups placed close to a subject fall off more slowly than $1 / d^2$.
- Direct light only: Bounce flash off ceilings or walls adds indirect light that reduces apparent falloff.
- No ambient mix: The calculation models only the single light you move; ambient exposure stays constant.
- Guide-number units: Match your distance unit (meters or feet) to the unit in your flash manual.
See our editorial policy for source standards.
Frequently Asked Questions
How many stops of light do you lose when you double the light distance?
Doubling the distance from a small light source reduces illuminance to one-fourth of its starting level, which equals a 2-stop loss. Because each stop halves the light, one-half times one-half equals one-fourth, requiring two stops of exposure compensation on your camera or flash.
How far do you move a light to change exposure by 1 stop?
Move the light by a factor of the square root of 2 (about 1.414) to change exposure by 1 stop. For example, moving a flash from 1.0 meter to 1.41 meters cuts the light in half (-1 stop), while moving from 1.41 meters to 1.0 meter doubles it (+1 stop).
Does the inverse square law apply to large softboxes and windows?
The inverse square law applies strictly to a point source whose size is small relative to the distance to the subject. When a large softbox or window sits close to a subject, light arrives from many angles across the diffuser, so falloff happens more slowly than the point-source formula predicts.
How do I calculate aperture from a flash guide number?
Divide the flash’s guide number (at ISO 100) by the flash-to-subject distance in the same unit (meters or feet). For example, a speedlight with a guide number of 30 meters at ISO 100 placed 3 meters away gives f/10 (30 ÷ 3 = 10).
Does raising ISO change a flash’s effective guide number?
Yes. Raising ISO increases sensitivity, so the effective guide number scales by the square root of (ISO ÷ 100). At ISO 400, √(400 ÷ 100) equals 2, which doubles the effective guide number and lets you stop down by two stops or place the flash proportionally farther away.
Sources
- HyperPhysics: Inverse Square Law for Light, checked 2026-11-14
- HyperPhysics: General Inverse Square Law, checked 2026-11-14
- Wikipedia: Exposure value, checked 2026-11-14
- Sony HVL-F46RM / HVL-F60RM2 Help Guide: Guide Number Table, checked 2026-11-14
- Canon Speedlite EL-1 Manual: Manual Flash Output Steps, checked 2026-11-14
Common questions
How many stops of light do you lose when you double the light distance?
Doubling the distance from a small light source reduces illuminance to one-fourth of its starting level, which equals a 2-stop loss. Because each stop halves the light, one-half times one-half equals one-fourth, requiring two stops of exposure compensation on your camera or flash.
How far do you move a light to change exposure by 1 stop?
Move the light by a factor of the square root of 2 (about 1.414) to change exposure by 1 stop. For example, moving a flash from 1.0 meter to 1.41 meters cuts the light in half (-1 stop), while moving from 1.41 meters to 1.0 meter doubles it (+1 stop).
Does the inverse square law apply to large softboxes and windows?
The inverse square law applies strictly to a point source whose size is small relative to the distance to the subject. When a large softbox or window sits close to a subject, light arrives from many angles across the diffuser, so falloff happens more slowly than the point-source formula predicts.
How do I calculate aperture from a flash guide number?
Divide the flash's guide number (at ISO 100) by the flash-to-subject distance in the same unit (meters or feet). For example, a speedlight with a guide number of 30 meters at ISO 100 placed 3 meters away gives f/10 (30 ÷ 3 = 10).
Does raising ISO change a flash's effective guide number?
Yes. Raising ISO increases sensitivity, so the effective guide number scales by the square root of (ISO ÷ 100). At ISO 400, √(400 ÷ 100) equals 2, which doubles the effective guide number and lets you stop down by two stops or place the flash proportionally farther away.
What we checked
- HyperPhysics: Inverse Square Law for Light, checked 2026-11-14 (hyperphysics.gsu.edu)
- HyperPhysics: General Inverse Square Law, checked 2026-11-14 (hyperphysics.gsu.edu)
- Wikipedia: Exposure value, checked 2026-11-14 (en.wikipedia.org)
- Sony HVL-F46RM / HVL-F60RM2 Help Guide: Guide Number Table, checked 2026-11-14 (helpguide.sony.net)
- Canon Speedlite EL-1 Manual: Manual Flash Output Steps, checked 2026-11-14 (cam.start.canon)
You might also like
- Photo and Video Lighting FAQ
Clear, source-backed answers to common beginner questions about natural light, LED vs. flash, white balance, video call lighting, and exposure.
- Photo and Video Lighting Glossary
Plain-English definitions of photo and video lighting terms—Kelvin, mired, CRI, TLCI, inverse square law, guide number, key light, and softbox.
- Free Photo and Video Lighting Tools
Free client-side calculators for photo and video lighting: Kelvin color temperature chart, inverse-square exposure, softbox softness, and golden hour.
- Camera Lighting Setup Checklist (Printable)
Printable pre-shoot lighting checklist covering power safety, natural light, white balance, key-light placement, glasses glare, and exposure.
- Golden Hour Calculator: Times for Any Location
Calculate sunrise, sunset, civil twilight, and morning or evening golden hour times for any latitude, longitude, and date using NOAA solar equations.
- Kelvin Color Temperature Chart and Light Matcher
Interactive Kelvin color temperature chart (1,000–10,000 K) and mired light matcher for camera white balance, built from Planck, CIE, and maker specs.